A wonderful innovation that is both beautiful and highly practical, this double bracket roller blind positions a sheer blind behind a blackout blind so they can be operated separately; allowing you amazing control over the amount of visibility and light entering your room.
Our double roller blinds have proven very popular for living rooms and open plan living spaces as you get the best of both worlds - reduced glare during the daylight hours from the sheer blind and complete privacy and light blockage from the blackout blind whenever its needed, usually in the evenings.
You can select from either a traditional sewn bottom finish on the two blinds, or aluminium bottom bars in a choice of white, silver or black. You can also use the related product shown above to add a smart cassette to your order that covers the top rolls of the blind for a neat, clean finish - we highly recommend doing this if you plan to face fix your blind outside of the recess. Simply add the 'Double Roller Blind Cassette' product to your basket as well as the blind itself.
We have created combinations using our most popular colours, however if you require different fabrics to those listed please contact us and we will advise if your selection is possible and supply a quotation.
Please Note This blind is suitable for top fixing only, it cannot be side fixed or face fixed.
Things to note :
The sheer blind will be standard rolled and positioned to the back nearest the window, while the blackout fabric will be reverse rolled and positioned at the front.
Sizing FAQ:
To order a recess size blind enter the wall to wall measurement at the smallest point of your window for for both width and drop. Our factory will make a small 1cm reduction to ensure your blind fits into this space.
An exact blind size is the finished blind size including brackets.
A fabric size blind is the size of the fabric part of the blind only - the finished blind will be 3.5cm wider than this to include for the brackets.
We will add enough fabric to the roll so that when the blind is fully extended the roller tube is still covered.
Please read the guide below and let us know which type of measurement you are providing:
Recess Size
If you want to fit your blind within the window recess as shown above, please provide us with Recess Size measurements.
To do this you will need to measure inside the window recess from wall to wall for the width and from ceiling to window sill for the drop.
You should take the measurements three times to make sure you get the most accurate sizes - at the top, at the middle and at the bottom for the width and at the top, the middle and the right for the drop.
The three sizes to give us are the smallest of the three measurements for both the width and the drop.
Make sure you do not make any reductions from these sizes yourself. We'll make your blinds slightly smaller on the width than the sizes you give us to make sure that it fits into the space with enough room for it to be installed easily and so the brackets don't scrape the walls, while still covering as much of the window as possible. The adjustment size will differ depending on the type of blind you choose and whether you are adding a cassette to cover the roll - our team will be happy to confirm the reduction amount for you if you advise which blind you are ordering.
Remember that the width of the fabric will always be slightly less than the total width of the blind to allow for the size of the mechanism and brackets - the difference is usually approximately 3.5cm.
Fabric Size or Blind Size
If you want to fit your blind outside of the window recess we recommend overlapping the window by at least 10cm on the width and 10cm on the drop.
You can then specify whether you want us to use these measurements as the Fabric Size or the Blind Size.
Fabric Size
If you choose Fabric Size we will use your measurements as the size of the fabric part of the blind only. This means that the size of the brackets/mechanism/cassette will be in addition to the sizes you provide us - this is usually 3.5cm but our team will be happy to confirm the amount for you before ordering.
Blind Size
If you choose Blind Size we will use your measurements as the size of the total blind including the brackets and mechanism (and cassette if ordered). This means that the fabric part of the blind will be slightly smaller than the sizes you provide. The amount of difference varies depending on the type of blind ordered - it is usually 3.5cm but our team will be happy to confirm the amount for you before ordering.
Help
Chain Colour Options
We offer a premium nickel chain as standard which offers smooth, precise control of your new roller blind.
Help
Bottom Finish Options
Please read the guide below and select which bottom finish option you would like from the drop down menu:
Plain Bottom Finish
Our plain bottom finish features a sturdy folded and sewn bottom pocket with a weighted insert to ensure the blind hangs nicely.
Aluminium Bottom Bars
Alternatively you can choose to have the bottom of your blind finished with an aluminium bottom bar in a range of finishes.
White Curved Bottom Bar
Black Curved Bottom Bar
Anthracite Grey Curved Bottom Bar
Silver Curved Bottom Bar
Please Note - In July 2023 our bottom bar options changed from a round aluminium bar to the rectangular Gemini bottom bar with a sleek curved front and stylish angled end caps. If you ordered previously and want to check if your new product's bottom bars will match those on your previous order, please contact our team who will be able to confirm.
Blackout Windsor Dark Grey and Sheer Dark Grey Double Roller Blind
This is a made to measure product. Place your order now and it will be despatched on or before Friday 11th April
